SCAPS-1D Analysis of Non-Toxic Lead-Free MASnI3 Perovskite-Based Solar Cell Using Inorganic Charge Transport Layers
Abstract
Perovskite solar cells (PSCs) have gained a lot of attention due to their high efficiency and low cost. In this research paper, a methylammonium tin iodide (CH3NH3SnI3) based solar cell was simulated using a one-dimensional solar cell capacitance simulation (SCAPS-1D) tool. The SCAPS-1D tool is based on Poisson and the semiconductor equations. After thorough investigation, the initial device presents the following parameters; power conversion efficiency (PCE)=15.315%, fill factor (FF)=64.580%, current density (Jsc)=29.152 mA/cm2, and open circuit voltage (Voc)=0.813 V. The effect of absorber and ETL thicknesses were explored systematically. The performance of the simulated device was significantly influenced by the thickness of the absorber and ETL. The optimized absorber thickness was 0.5 µm and the ETL thickness was 0.02 µm, giving rise to an optimized PCE of 15.411%, FF of 63.525%, Jsc of 29.812 mA/cm2, and Voc of 0.814 V. Additionally, the effect of temperature on the optimized device was evaluated and found that it affects the performance of the device. This model shows the prospect of CH3NH3SnI3 as a perovskite material to produce toxic-free environment-friendly solar cells with high efficiency.
Downloads
References
A. Kojima, K. Teshima, Y. Shirai, and T. Miyasaka, “Organometal Halide Perovskites as Visible-Light Sensitizers for Photovoltaic Cells,” J. Am. Chem. Soc. 131(17), 6050–6051 (2009). https://doi.org/10.1021/ja809598r
E. Danladi, et al., “Defect and doping concentration study with series and shunt resistance influence on graphene modified perovskite solar cell: A numerical investigation in SCAPS-1D framework,” Journal of the Indian Chemical Society, 100(5), 101001 (2023). https://doi.org/10.1016/j.jics.2023.101001
E. Danladi et al., “Broad-band-enhanced and minimal hysteresis perovskite solar cells with interfacial coating of biogenic plasmonic light trapping silver nanoparticles,” Materials Research Innovations, 27(7), 521–536 (2023). https://doi.org/10.1080/14328917.2023.2204585
Z. Qu, F. Ma, Y. Zhao, X. Chu, S. Yu, and J. You, “Updated Progresses in Perovskite Solar Cells,” Chinese Phys. Lett. 38(10), 107801 (2021). https://doi.org/10.1088/0256-307X/38/10/107801
M.K. Hossain, et al., “Numerical simulation and optimization of a CsPbI3-based perovskite solar cell to enhance the power conversion efficiency,” New J. Chem. 47(10), 4801–4817 (2023). https://doi.org/10.1039/D2NJ06206B
M.K. Hossain, et al., “Deep Insights into the Coupled Optoelectronic and Photovoltaic Analysis of Lead-Free CsSnI3 Perovskite-Based Solar Cell Using DFT Calculations and SCAPS-1D Simulations,” ACS Omega, 8(25), 22466–22485 (2023). https://doi.org/10.1021/acsomega.3c00306
S.D. Stranks, and H. J. Snaith, “Metal-halide perovskites for photovoltaic and light-emitting devices,” Nature Nanotech. 10(5), 391–402 (2015). https://doi.org/10.1038/nnano.2015.90
Md.R. Islam, A.A.M. Mazumder, Md.R.H. Mojumder, A.S.M.Z. Shifat, and M.K. Hossain, “Strain-induced tunable optoelectronic properties of inorganic halide perovskites APbCl3 (A = K, Rb, and Cs),” Jpn. J. Appl. Phys. 62(1), 011002 (2023). https://doi.org/10.35848/1347-4065/acb09e
A. Thakur, D. Singh, and S.K. Gill, “Numerical simulations of 26.11% efficient planar CH3NH3PbI3 perovskite n-i-p solar cell,” Materials Today: Proceedings, 71, 195–201 (2022). https://doi.org/10.1016/j.matpr.2022.08.423
H. Bencherif, et al., “Performance enhancement of (FAPbI3)1-x(MAPbBr3)x perovskite solar cell with an optimized design,” Micro and Nanostructures, 171, 207403 (2022). https://doi.org/10.1016/j.micrna.2022.207403
H. Bencherif, and M.K. Hossain, “Design and numerical investigation of efficient (FAPbI3)1−x(CsSnI3)x perovskite solar cell with optimized performances,” Solar Energy, 248, 137–148 (2022). https://doi.org/10.1016/j.solener.2022.11.012
Y. Zhou, and K. Zhu, “Perovskite Solar Cells Shine in the ‘Valley of the Sun,’” ACS Energy Lett. 1(1), 64–67 (2016). https://doi.org/10.1021/acsenergylett.6b00069
B.V. Lotsch, “New Light on an Old Story: Perovskites Go Solar,” Angew Chem. Int. Ed. 53(3), 635–637 (2014). https://doi.org/10.1002/anie.201309368
H. Sabbah, “Numerical Simulation of 30% Efficient Lead-Free Perovskite CsSnGeI3-Based Solar Cells,” Materials, 15(9), 3229 (2022). https://doi.org/10.3390/ma15093229
E. Danladi, A.O. Salawu, M.O. Abdulmalik, E.D. Onoja, E.E. Onwoke, and D.S. Adepehin, “Optimization of Absorber and ETM Layer Thickness for Enhanced Tin based Perovskite Solar Cell Performance using SCAPS-1D Software,” PA, 02(01), 1–11 (2022). https://doi.org/10.47514/phyaccess.2022.2.1.001
E. Danladi, M. Kashif, A. Ichoja, and B. B. Ayiya, “Modeling of a Sn-Based HTM-Free Perovskite Solar Cell Using a One-Dimensional Solar Cell Capacitance Simulator Tool,” Trans. Tianjin Univ. 29(1), 62–72 (2023). https://doi.org/10.1007/s12209-022-00343-w
W. Shockley, and H.J. Queisser, “Detailed Balance Limit of Efficiency of p-n Junction Solar Cells,” Journal of Applied Physics, 32(3), 510–519 (1961). https://doi.org/10.1063/1.1736034
D. Jalalian, A. Ghadimi, and A. Kiani, “Modeling of a high performance bandgap graded Pb-free HTM-free perovskite solar cell,” Eur. Phys. J. Appl. Phys. 87(1), 10101 (2019). https://doi.org/10.1051/epjap/2019190095
M.K. Hossain, et al., “An extensive study on multiple ETL and HTL layers to design and simulation of high-performance lead-free CsSnCl3-based perovskite solar cells,” Sci. Rep. 13(1), 2521 (2023). https://doi.org/10.1038/s41598-023-28506-2
M.K. Hossain, et al., “Numerical Analysis in DFT and SCAPS-1D on the Influence of Different Charge Transport Layers of CsPbBr3 Perovskite Solar Cells,” Energy Fuels, 37(8), 6078–6098 (2023). https://doi.org/10.1021/acs.energyfuels.3c00035
J. Chen, and N.-G. Park, “Inorganic Hole Transporting Materials for Stable and High Efficiency Perovskite Solar Cells,” J. Phys. Chem. C, 122(25), 14039–14063 (2018). https://doi.org/10.1021/acs.jpcc.8b01177
E. Danladi, et al., “Highly efficient, hole transport layer (HTL)-free perovskite solar cell based on lithium-doped electron transport layer by device simulation,” Emergent Mater. 6(6), 1779–1795 (2023). https://doi.org/10.1007/s42247-023-00558-0
M.K.A. Mohammed, “High-performance hole conductor-free perovskite solar cell using a carbon nanotube counter electrode,” RSC Adv. 10(59), 35831–35839 (2020). https://doi.org/10.1039/D0RA05975G
N. Fakhri, M.S. Naderi, S.G. Farkoush, S.S. Nahaei, S.-N. Park, and S.-B. Rhee, “Simulation of Perovskite Solar Cells Optimized by the Inverse Planar Method in SILVACO: 3D Electrical and Optical Models,” Energies, 14(18), 5944 (2021). https://doi.org/10.3390/en14185944
S. Zandi, P. Saxena, and N.E. Gorji, “Numerical simulation of heat distribution in RGO-contacted perovskite solar cells using COMSOL,” Solar Energy, 197, 105–110 (2020). https://doi.org/10.1016/j.solener.2019.12.050
M.K. Hossain, M.H.K. Rubel, G.F.I. Toki, I. Alam, Md.F. Rahman, and H. Bencherif, “Effect of Various Electron and Hole Transport Layers on the Performance of CsPbI 3 -Based Perovskite Solar Cells: A Numerical Investigation in DFT, SCAPS-1D, and wxAMPS Frameworks,” ACS Omega, 7(47), 43210–43230 (2022). https://doi.org/10.1021/acsomega.2c05912
E. Danladi, et al., “Modeling and simulation of > 19% highly efficient PbS colloidal quantum dot solar cell: A step towards unleashing the prospect of quantum dot absorber,” Optik, 291, 171325 (2023). https://doi.org/10.1016/j.ijleo.2023.171325
P.K. Jha, et al., “Study of Eco-Friendly Organic–Inorganic Heterostructure CH3NH3SnI3 Perovskite Solar Cell via SCAPS Simulation,” J. Electron. Mater. 52(7), 4321–4329 (2023). https://doi.org/10.1007/s11664-023-10267-3
K. Nishimura, et al., “Lead-free tin-halide perovskite solar cells with 13% efficiency,” Nano Energy, 74, 104858 (2020). https://doi.org/10.1016/j.nanoen.2020.104858
H.-J. Du, W.-C. Wang, and J.-Z. Zhu, “Device simulation of lead-free CH3NH3SnI3 perovskite solar cells with high efficiency,” Chinese Phys. B, 25(10), 108802 (2016). https://doi.org/10.1088/1674-1056/25/10/108802
Guo, et al., “Effects of Transition Metal Substituents on Interfacial and Electronic Structure of CH3NH3PbI3/TiO2 Interface: A First-Principles Comparative Study,” Nanomaterials, 9(7), 966 (2019). https://doi.org/10.3390/nano9070966
N.J. Valeti, K. Prakash, and M.K. Singha, “Numerical simulation and optimization of lead free CH3NH3SnI3 perovskite solar cell with CuSbS2 as HTL using SCAPS 1D,” Results in Optics, 12, 100440 (2023). https://doi.org/10.1016/j.rio.2023.100440
M. Liu, M.B. Johnston, and H.J. Snaith, “Efficient planar heterojunction perovskite solar cells by vapour deposition,” Nature, 501(7467), 395–398 (2013). https://doi.org/10.1038/nature12509
O.A. Muhammed, E. Danladi, P.H. Boduku, J. Tasiu, M.S. Ahmad, and N. Usman, “Modeling and Simulation of Lead-Free Perovskite Solar Cell Using SCAPS-1D,” EEJP, (2), 146-154 (2021). https://doi.org/10.26565/2312-4334-2021-2-12
N.F. Mott, and E.A. Davis, Electronic processes in non-crystalline materials, 2nd ed. in International series of monographs on physics, (Clarendon Press, Oxford, 2012).
I. Qasim, et al., “Numerical optimization of (FTO/ZnO/CdS/CH3NH3SnI3/GaAs/Au) perovskite solar cell using solar capacitance simulator with efficiency above 23% predicted,” Opt. Quant. Electron. 53(12), 713 (2021). https://doi.org/10.1007/s11082-021-03361-5
S. Ahmed, F. Jannat, Md.A.K. Khan, and M.A. Alim, “Numerical development of eco-friendly Cs2TiBr6 based perovskite solar cell with all-inorganic charge transport materials via SCAPS-1D,” Optik, 225, 165765 (2021). https://doi.org/10.1016/j.ijleo.2020.165765
Copyright (c) 2024 Matthew I. Amanyi, Abubakar S. Yusuf, Eghwubare Akpoguma, Stephen O. Eghaghe, James Eneye, Raymond M. Agaku, Lilian C. Echebiri, Emmanuel U. Echebiri, Emmanuel O Ameh, Chinyere I. Eririogu, Nicholas N. Tasie, Anthony C. Ozurumba, Eli Danladi
![Creative Commons License](http://i.creativecommons.org/l/by/4.0/88x31.png)
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).