Development of a normative base for resource-saving technologies in mechanical processing
Abstract
DOI: https://doi.org/10.32820/2079-1747-2019-23-94-99
The aim of the work is to analyze energy transformations in the finishing turning of steel with carbide-tipped cutting blades with the subsequent development of the regulatory framework for resource-saving technologies for machining. Universal theoretical models for determining the optimal cutting conditions should be based on consideration of the cutting process as a complex of interrelated phenomena, the intensity of each of which can be expressed through a single integral energy criterion. A significant number of interconnected physical processes in steel turning with a carbide tool with reinforcement or wear-resistant coating and the dependence of their intensity on cutting conditions and properties of the surface layer of the tool acquired by it as a result of reinforcing effect requires a comprehensive analysis of the links of the integrated energy criterion of the cutting process with cutting conditions.
The article formulated a system of links of the integral energy criterion of the cutting process with cutting conditions. During machining, the energy consumption required for chip removal is reduced by 10-15%, if not the maximum allowance is removed, but probabilistic. The consumption of thermal energy going to heat the workpiece when turning decreases by 20% when removing the actual allowance. A useful part of the energy balance will be considered constant for a given pair of "solid glow - processed material". The minimum of thermal energy or any increase in internal energy is required and sufficient to form a surface when removing the material layer with a given section of the cut. The surplus of the energy component that exceeds this minimum will be considered as a "harmful" part, which is spent on the intensification of contact processes, and, accordingly, on the demolition of the instrument. In the article on the basis of the analysis of energy transformations in the finishing of steel by cutters with carbide cutting plates, the system of connections of the integral energy criterion of cutting process with cutting modes was formulated. When machining the amount of energy needed to remove chips, it decreases if not the maximum allowable, but probabilistic. The consumption of heat energy, which goes to the heating of the workpiece at the precision, decreases, with the removal of the actual allowance.
Downloads
References
Tatjanchenko, AG & Lappo, IN 2013, ‘Osobennosti razvitija teplovyh processov pri chistovoj obrabotke otverstij kombinirovannym osevym instrumentom’, Visnyk Sevastopolskoho natsionalnoho tekhnicheskoho uniersytetu, Seriia Mashynopryladobuduvannia ta transport, Sevastopol, iss. 140, pp. 178-183.
Reznikov, AN & Jacenko, LE 1973, ‘Termouprugie deformacii izdelija i instrumenta v processe razvertyvanija’, Teplofizika tehnologicheskih processov, Izdatelstvo Saratovskogo universiteta, Saratov, iss. 1, pp. 24-35.
Tatianchenko, OH 2006, ‘Teoretychni osnovy prohnozuvannia termopruzhnykh deformatsii osovoho instrumentu i detali i yikh vplyv na tochnist obrobky otvoriv’, Doct.tech.n. abstract, Donetskyi natsionalnyi tekhnichnyi universytet, Donetsk.
Tatianchenko, AG, Lappo, IN & Brizhan, TM 2013, ‘Perspectives of heightening of exactitude fair handlings of holes by the axial instrument’, Strategy of Quality in Industry and Education, Varna, vol. 3, pp. 202-207.
Malyshko, IA & Tatjanchenko, AG 2001, ‘Temperaturnye deformacii detali pri obrabotke otverstij’, Progressivnye tehnologii i sistemy mashinostroenija, Doneck, iss. 17, pp. 45-51.
Malyshko, IA, Tatjanchenko, AG & Bocharov, SI 2001, ‘Temperaturnoe sostojanie detali pri razvertyvanii otverstij’, Visnyk inzhenernoi akademii, Kyiv, no. 3, pp. 231-233.
Lappo, IM 2016, ‘Udoskonalennia normatyvnoi dokumentatsii zabezpechennia yakosti lezovoi obrobky otvoriv’, Kand.tech.n. thesis, Kharkiv.
Danieljan, AM 1950, Rezanie metallov i instrument, Gosudarstvennoe nauchno-tehnicheskoe izdatelstvo mashinostroitelnoj literatury, Moskva.
Rozenberg, JuA 2007, Rezanie materialov, Poligraficheskij kombinat, Kurgan.
Jashhericyn, TI, Feldshtejn, EJe & Kornievich, MA 2006, Teorija rezanija, 2nd edn, Novoe znanie, Minsk.
Metodicheskie ukazanija. Vybor universalnyh sredstv izmerenija linejnyh razmerov do 500 mm. (Po primeneniju GOST 8.051–81): RD 50–98–89 1987, Izdatelstvo standartov, Moskva.
Silin, RI, Mjasishhev, AA & Kovalchuk, SS 1989, ‘Analiz processa snjatija struzhki metala rezhushhim klinom’, Izvestija vuzov, Mashinostroenie, no. 2, pp. 145-148.